Others in this category

Berger Everglow Low-Sheen Emulsion

Berger Everglow is one of the most versatile, low VOC, pure acrylic emulsions, offering great beauty and protection inside and out.

Berger Everglow has been specially formulated to provide protection against cracking, peeling and chalking whilst offering salt and dirt-resistant properties. Everglow is fungus and algae resistant and is easy to apply by brush, roller or spray. Its superb adhesion, great coverage and easy clean-up in water make Everglow a great product for wood and wall. Everglow is available in thousands of Spectra 1800 colours that add beauty and long-lasting protection on exterior and interior surfaces. Great in high-traffic spaces and surfaces requiring frequent washing and water resistance.

Features

Low VOC

Complies with global environmental standards with minimal impact on the environment

Anti-Fungal and Anti-Algal Properties

Prevents mould and algae from forming on the surface

Dries in 15 minutes

Fast drying, so painted areas may be used more quickly

Available in over 1800 colours

Making thousands of colour options for you to choose from

Very Low odour

Easy to use in occupied living spaces

Superior Scrubbability

Easy to clean and withstands multiple washings

For interior and exterior use

Versatile inside and out

Finishes –
Low Sheen

Surface preparation:

  • Previously painted surfaces should be sound and cleaned thoroughly
  • Rub down with fine grade sandpaper and prime with appropriate Berger Primer
  • Concrete should be free from loose sand and efflorescence
  • Wire-brush Lime-washed surfaces and prime in Penetrating Liquid or Alkali Sealer

Application Procedure:

  • Brush, Roller or Spray
  • Stir gently before application to avoid the incorporation of air
  • For best results, apply one coat of Berger Alkali Sealer to prime all new concrete/cement surfaces
  • Before applying to wood, apply one coat of Berger Grip & Seal Multi-Surface Primer

Tips: Make sure to use the right roller for the job. Use a 10-12mm nap on walls and 20-32mm nap covers on rough surfaces like concrete or textured walls.

Tools you will need

Paint Brush
Paint Roller
Spray Gun

Available Packs

1 Coat

9.0 m2/Ltr**

Coverage

On well-prepared surfaces, as per the painting system recommended. Please refer to the Product Data Sheet for surface preparation and method of application.

** Actual coverage may vary from the quoted coverage due to factors such as method and condition of application, surface roughness, and porosity.

Washability

Best-in-class

High

Medium

Low

The splitting of dry paint film through at least one coat. In early stages it appears as hairline cracks and in the later stages flaking occurs.

What are the possible causes?

  • Applying low quality paint to the surface, with inadequate adhesion and flexibility
  • Applying too thin a coat of paint to the surface
  • Inadequate surface preparation
  • Failure to prime bare wood before top-coating
  • Oil paint hardens with age, until it eventually cracks
  • Painting on damp wood

What is the solution?

  • Remove loose paint or flaking paint by scraping or wire brushing
  • Sand the area to feather the edges
  • Prime bare spots
  • Repaint with two coats of a premium paint
  • Berger recommends 2 topcoats over 1 primer coat

We recommend you use these painting systems in order of base coat, first coat, and second coat:

Foaming and cratering frequently occur when bubbles form. When the bubbles break during application and drying, they result in small, round concave depressions or cratering.

What are the possible causes?

  • Shaking a partially filled can of paint
  • Applying paint too rapidly, especially rolling
  • Using low-quality paint or very old latex paint
  • Using a roller cover with the wrong nap length
  • Excessively rolling or brushing the paint
  • Applying a gloss or semi-gloss paint over a painted surface

What is the solution?

  • All paints will foam to some extent during application
  • Premium quality paints are specially formulated, so the bubbles break while the paint is wet, allowing for good flow and appearance
  • Avoid excessive rolling or brushing of the paint or using old paint
  • Apply gloss and semi-gloss paints with a short nap roller
  • Apply appropriate primer/sealer when painting over a porous surface
  • Problem areas should be sanded before repainting

We recommend you use these painting systems in order of base coat, first coat, and second coat:

Patchiness generally occurs when insufficient paint has been applied or when paint is applied unevenly, resulting in a variation of the film build leading to patches.

What are the possible causes?

  • Inconsistent distribution of paint on the surface
  • Incorrect or low quality paint brush or roller
  • Failure to apply a primer over joint compound
  • Applying paint over joint compound not fully dried
  • The top coat is applied over spot-puttied surfaces
  • Variations in surface gloss can cause paint to appear patchy

What is the solution?

  • Increase the amount of paint on the brush or roller to allow better distribution
  • Apply the paint in a grid fashion to ensure an even finish
  • Allow puttied wall to dry evenly before priming
  • By applying one coat of appropriate premium Berger Primer
  • Apply two coats of premium Berger acrylic topcoat
  • Refer to Berger Technical Support for primer options

We recommend you use these painting systems in order of base coat, first coat, and second coat:

Peeling often occurs when high levels of moisture penetrate the paint film, eventually pushing it away from the surface.

What are the possible causes?

  • Excessive atmospheric moisture, e.g. shower
  • Excessive moisture due to high humidity, e.g. basement and/or foundation

What is the solution?

  • Remove loose paint by scraping or wire-brushing
  • Remove any efflorescence and mildew
  • Power wash with plain water
  • Scrape cracks clean of debris and seal with Berger acrylic caulk
  • Remove residual dust particles, taking care to not let water into cracks or porous areas
  • Apply premium Berger primer for best durability and resistance
  • Always overcoat primer with premium topcoat

We recommend you use these painting systems in order of base coat, first coat, and second coat:

Picture framing occurs when the brushed areas appear darker than the areas painted with roller, resembling a picture frame.

What are the possible causes?

  • Applying paint at different thicknesses in brush and roller application
  • Failure to keep a wet edge while painting
  • Incomplete mixing resulting in paint not being uniformly incorporated
  • Using a roller cover nap that is too long, which will produce a heavy texture
  • Using of different techniques in the same area, such as spraying and brushing

What is the solution?

  • Ensure similar spread rates with brushes and rollers
  • Don’t cut in the entire room before roller coating
  • Work in smaller sections of the room to maintain a “wet edge”
  • Ensure correct colorant-base combinations are used
  • Ensure uniform mixing of the paint

We recommend you use these painting systems in order of base coat, first coat, and second coat:

Failure of paint to stick to the surface on which it has been applied and/ or to itself can be described as poor adhesion.

What are the possible causes?

  • The biggest cause of poor adhesion is poor surface preparation
  • Insufficient sanding before applying any primer
  • Applying primer too thin
  • Diluting the primer thereby weakening its ability to stick to the surface
  • Failure to prime the surface in the first place
  • Painting wet or damp surface
  • Incompatible coatings, such as a water based coating over oil

What is the solution?

  • Use the correct type of primerfor the surface
  • Apply primer following manufacturer’s recommendations
  • Never paint on a wet or a damp surface
  • Always ensure that the area is clean, dry and free from contaminants before painting
  • Treat any surface problems before priming
  • Ensure that primers and topcoats are compatible and suitable for the surface being painted

We recommend you use these painting systems in order of base coat, first coat, and second coat:

Poor hiding occurs when paint fails to obscure or hide the surface to which it is applied.

What are the possible causes?

  • Using low-quality paint with little hiding power
  • Spreading paint too thinly or unevenly
  • Over-thinning paint beyond the recommended amount
  • Failure to prime the surface before top-coating
  • Painting a porous or absorbent surface
  • Using incorrect or poor quality tools
  • Inadequately mixed paint

What is the solution?

  • Prime first, if moving from a significantly darker to a light colour
  • When painting in a dark colour, tint primer in a similar tone to the topcoat shade
  • Use premium quality paint for better hiding and flow
  • Use quality and correct tools for the job
  • Follow manufacturer’s recommendation for thinning

We recommend you use these painting systems in order of base coat, first coat, and second coat:

The easy wearing away of paint when scrubbed with a brush, sponge, or cloth is indicative of a paint which is exhibiting poor scrub resistance.

What are the possible causes?

  • Insufficient time allowed for paint to fully dry before washing or scrubbing
  • Use of an abrasive cleaner
  • Choosing the wrong product or sheen for the area
  • Using low quality paint
  • Overly aggressively scrubbing the painted area

What is the solution?

  • Areas requiring frequent washing will require a high quality paint formulated especially to provide such performance
  • High traffic areas may require a silk, semi-gloss or gloss rather than a flat paint
  • Allow adequate dry time, as scrub resistance will not fully develop until the paint has thoroughly cured. Typically, 5 days
  • Use non-abrasive material and mild detergent where possible

We recommend you use these painting systems in order of base coat, first coat, and second coat:

Failure of paint to dry to a smooth film, resulting in unsightly, unintentional brush or roller marks after the paint has dried.

What are the possible causes?

  • Re-brushing or re-rolling fresh paint on partially dried paint
  • Applying paint too rapidly or for too long
  • Using wrong type or poor quality brush, roller or nap size
  • Applying too thin of a paint film
  • Painting a hot surface or in direct sunlight
  • Coating a very porous surface
  • Incorrect rolling technique

What is the solution?

  • Allow paint to dry thoroughly before applying second coat
  • Wait until the paint has dried thoroughly before touching up
  • Use correct rolling or brushing technique
  • Follow label directions for appropriate quality, applicator size, and type needed
  • Follow label directions for correct film build
  • Prime to seal porous surfaces

We recommend you use these painting systems in order of base coat, first coat, and second coat:

The hardening on the outer layer of a thick coat of paint before the under layer dries results in the paint film having a rough, wrinkled appearance.

What are the possible causes?

  • Applying paint too thickly especially with oil-based paints
  • Applying a second coat of paint before the first has dried
  • Not following recommended drying times
  • Painting during extremely hot climate causes the paint film to dry faster on top than on the bottom
  • Uncured paint that is exposed to high humidity is also prone to wrinkling
  • Painting over contaminated surface e.g., dirt, grease or wax

What is the solution?

  • Allow wrinkled coating to dry completely
  • Once dry, scrape or sand to remove wrinkled coating
  • In reapplying paint, follow recommended drying between coats
  • Avoid extremes in humidity and heat during application
  • Use premium quality exterior paint
  • It’s always better to apply two thin coats, than one thick coat
  • Consider using a water-based system for a shorter drying and recoating time

We recommend you use these painting systems in order of base coat, first coat, and second coat:

The yellow cast that appears over previously painted white surfaces is called yellowing, and mostly occurs with oil paints.

What are the possible causes?

  • Use of oil paint in areas not receiving direct sunlight
  • Oxidation of alkyd or oil-based paint or varnish as it ages
  • Heat from stoves, radiators and heating ducts will turn oil paint yellow
  • Lack of light in dark areas such as behind picture frames, appliances and inside closets
  • Tobacco staining or other environmental contaminants

What is the solution?

  • Because of their drying process water-based painting systems fear better in enclosed areas
  • Water-based acrylic paints are non-yellowing
  • If your preference is for oil paint, ensure maximum sunlight to minimise yellowing

We recommend you use these painting systems in order of base coat, first coat, and second coat:

We also recommend

Colour
Library

Choose from over 2000+ colours

Colour Visualiser

Colour
Tools

Paint Calculator

Calculate how much paint you need

keyboard_arrow_up